3HAC
在诊断输入输出故障时，方法是区分究竟是模块自身的问题，还是现场连接上的问题。如果有电源指示器和逻辑指示器，模块故障易于发现。通常，先是更换模块，或测量输入或输出端子板两端电压测量值正确，模块不响应，则应更换模块。若更换后仍无效，则可能是现场连接出问题了。输出设备截止，输出端间电压达到某一预定值，就表明现场连线有误。若输出器受激励，且LED指示器不亮，则应替换模块。如果不能从模块中查出问题，则应检查模块接插件是否接触不良或未对准。最后，检查接插件端子有无断线，模块端子上有无虚焊点。
Allen Bradley Reverse Motor Starter Size 2 705-COD23 Ser K #7584
Revere Load Cell Tranducer #62092
(L7) 1 ABB XUSI03175 ROBOTICS BOARD
Hydro Line Cylinder N5P-3.25X1 #44668
FURNAS 22EP32AE6 STARTER
1 Parker N0C111P3 Enclosed Coil (O4-5)
Barber Colman Control Card Rack 40BA-2G1AC-CCA-A-00 Scratch & Dent #36005
Van Dorn Machine Operation & Maintenance Manual MTD(P) #65163
GE MSV Amp Card G2
Narda 8741, 0.3 to 40.0 GHz, 20 mW/cm^2, Isotropic Electric Field Probe Assy.
IFM 0G5056 SENSOR
Vickers Directional Control Valve DG5S82CMFWB530 #65939
(L14) 1 NIB ASCO JKB8320G174MS VALVE
Van Dorn End Cap EC-VD #38196
Morrell Inc. 60 ft. Cable H18-MPT/FPT-16P-060 #56433
Allen Bradley 8 Slot Rack 1860-RB8W5 #29151
(8941) Allen Bradley MIni Plc-2/16 Processor 1772-LXP w/ KEY
Maury Microwave 299-D-011 (A034B) 0.00025" to 0.050" Range, 3.5mm Connector Gage
(0376) Fuji Circuit Breaker 350A BU-KSB3350 3P 600VAC
HI-Shear Spacematic M100 ll, 90 PSI, .45 HP, Precision Pneumatic Drill + Motor
HyperLink Technologies HyperAmp H2401-AGC1000, 1W, Bi-Directional Amplifier,
Helm Circuit Board B10A333-1C #51060
BUSSMANN FWP-450A FUSE
LOT OF 10 FERRAZ SHAWMUT AJT10 FUSES
EAGLE SIGNAL DZ100A3 COUNTER
HP (3332IT) DC to 22 GHz 24 VDC SMA (F-F) Programmable Attenuator,
Generic Watt Ceramic Heater Band HD #68858
HP / Agilent 71500 Series Installation and Verification Manual
Yaskawa Circuit Board JANCD-MCP02B-1 Rev D0 #76702
Barber Colman Data Handler PC Board A #19658
Texscan (Trilithic) FP-75 (10 dB) DC to 1 GHz, 75 Ohm, BNC, Coaxial Attenuator
(RR23-1) INPRO/SEAL COMPANY 1000-S BEARING ISOLATOR
