操作简单易用；抛光抛不到的焊点，它都可以轻易处理到。
比用洗钢水和抛光速度更快更经济不会生锈。
做不锈钢工程可以把焊道转移到管与管的管缝中间使产品更具美观，变形更小
使用时与焊道处理液，于清洁布配套使用
一个整流桥堆，一个过流保护开关，完全解决了你的后顾之忧。有点电工基础的知道大功率全铜芯的线圈是不会有任何问题。
凯盟科研不锈钢焊道处理剂，用于不锈钢工件焊接后的焊缝处理清洗处理，安全简单操作，效率极高，不容易损坏，使用寿命长，药水消耗率低，用完之后绿色环保，无药水残留。
Brief introduction
It is made of polymer compound as the main agent,high quality corrosion inhibitor,complexing agent and electric ion
accelerator.It is colorless,tasteless and doesn’t contain chromic acid.Importantly, it is in line with the standard
of RoHS and FDA.Meanwhile, it can pass the inspection of SGS and certification of GMP.Saving the invest of
environmental protection equipment and cost of wastewater treatment is our biggest advantage.Special light and
environmental treatment efficacy is especially on food production and medical equipment which are stainless steel.
Strong commonality and convenient.It is suitable for the electrolytic olishing of SUS300(such as SUS
SUS200(such as SUSand 3Cr13,2Cr13,SUS430.
Characteristics and advantages
·Electrolytic polishing has an effect of mirror gloss level and up to Ra0.2 ~ 0.5μ. Moreover, the ability of anti-corrosion will be enhanced.
·Small consumption current, low voltage.Power consumption is lower than the traditional process more than 1 times
·long service life, easy to maintain and manage.Only master the proportion of polishing solution can be very good control of production.
·It can polishing the surface of metal that machine polishing cannot reach .Such as pits, complex parts, filaments, thin films and mesh object.
· It obtains good flatness by remove the micro burr effectively.
焊缝清洗机是一款专门用于清除不锈钢焊接后所产生的焊斑以及黑色氧化物的设备。在通电的状况下，只需要将毛刷沾上“焊缝抛光液”几秒钟时间即可清除和抛光出很光亮的焊缝。能替代人工的机械打磨，不但效率更快，而且机械打磨不能处理的死角位置也能很轻松的处理。焊缝抛光机具有全自动短路保护、其线路不仅可以自动闭合进行断路保护，并可自动启动，无需再次手动启动。——全程自动开关，仅需手握处理手柄，就像刷油漆一样，对准黑色焊缝道斑点快速来回刷拭，黑色焊斑即刻消失，极大地提高了工作效率
1、 只能是不锈钢材料的焊缝才适合用焊缝抛光机，比如SUS04、316……和SUShellip;…其他材料一律不适用。
2、 必须同时购买“焊缝抛光液”才能使用。“焊缝抛光液”和“毛刷”属于消耗品。
3、 装箱清单：主件：焊缝处理机1台，地线夹1套，抛光枪1套，包布枪1套。附件：毛刷2个，保险丝3条，电刷布1包。
