|
Model ZQ1S4 Emission standards of country 5 The maximum lifting weight is 1200kg The number of boom sections is 1.3m *4 Boom belt load expansion Maximum lifting height 5m Maximum lifting torque 1.56T*M Rated flow of hydraulic system is 25L/min The maximum working range is 4m Rotation Angle 180 Luffing Angle - 65 ° ~ 75 ° The crane has a dead weight of 500kg Chassis tang jun (optional) Instructions for use of car crane Avoid overload. 2. Determine whether it is allowed to use according to the ground conditions. 3. Load the goods correctly. 4. Please wear safety shoes and gloves when operating. 5. Please make a thorough operation check before each use. 6. Before the test, the adjusting rod of the balance beam and the lifting arm should be fully pre-tightened. 7. Items shall not be slanted along the direction of the main beam. 8. The cable length of the motor shall be noted when the crane rotates. Continuous rotation in the same direction is not allowed to prevent the cable from being torn. 1.2t folding boom truck crane is a small 1.2t truck crane with telescopic load Purchased 1.2 ton folding boom crane with 360 degree rotation and full hydraulic load expansion The standard 1.2-ton folding boom crane can be equipped with kmart, tang jun, dayun, sinotruk ace and sinotruk haumann chassis crane Avoid overload. 2. Determine whether it is allowed to use according to the ground conditions. 3. Load the goods correctly. 4. Please wear safety shoes and gloves when operating. 5. Please make a thorough operation check before each use. 6. Before the test, the adjusting rod of the balance beam and the lifting arm should be fully pre-tightened. 7. Items shall not be slanted along the direction of the main beam. 8. The cable length of the motor shall be noted when the crane rotates. Continuous rotation in the same direction is not allowed to prevent the cable from being torn. |
ZQ1S4 |
|
排放标准 |
国五 |
|
最起重量 |
1200kg |
|
吊臂节数 |
1.3米*4节 |
|
吊臂 |
带载伸缩 |
|
最起升高度 |
5m |
|
最起重力矩 |
1.56T*M |
|
液压系统额定流量 |
25L/min |
|
最工作幅度 |
4m |
|
回转角度 |
±180 |
|
变幅角度 |
-65°~~75° |
|
起重机自重 |
500kg |
|
底盘 |
唐骏（选配） |
车载吊机使用说明
1. 避免超载。
2.根据地面条件判定是否允许使用。
3.正确装载货物。
4.操作时请穿戴好安全鞋和手套。
5.每次使用前请做一次彻底的操作检查。
6.试车前，平衡梁和吊臂的调节拉杆应充分预紧。
7.不得沿主梁方向斜吊物品。
8.吊机旋转时应注意到电机的电缆长度，不允许连续同方向旋转，防止电缆扯断。
1.2吨折臂随车吊 可带载伸缩的1.2吨小型随车吊
采购1.2吨折臂吊 360度旋转 全液压带载伸缩
国五标配的1.2吨折臂吊 可选配凯马，唐骏，大运，重汽王牌，重汽豪曼底盘车载吊机使用说明
1. 避免超载。
2.根据地面条件判定是否允许使用。
3.正确装载货物。
4.操作时请穿戴好安全鞋和手套。
5.每次使用前请做一次彻底的操作检查。
6.试车前，平衡梁和吊臂的调节拉杆应充分预紧。
7.不得沿主梁方向斜吊物品。
8.吊机旋转时应注意到电机的电缆长度，不允许连续同方向旋转，防止电缆扯断。
