Snowmaker/snowdrifter
外形尺寸0mm
Shape size00mm
重量820kg
Weight 820Kg
额定电压380v
Rated voltage 380V
主风机15kw（主风机电机二次起动）
Main fan 15 kW (secondary starting of main fan motor)
压缩机7.5kw
Compressor 7.5kw
加热6kw
Heating 6 kW
核子器20
Nucleon 20
水喷嘴360（自动摆头35°~45°）
Water nozzle 360 (automatic head swing 35 ~45)
旋转范围360度
Rotation range 360 degrees
喷桶倾角45度
Spray bucket inclination 45 degrees
水接口2"寸
Water interface 2 inches
工作水压8-45bar
Working water pressure 8-45 bar
zui大出水量12-46立方米
Zui large water output 12-46 cubic meters
射程55米
Range 55 meters
实拍效果图
Picture effect
金耀造雪机参数
Parameters of Jinyao Snowmaker
外形尺寸 ：长2600mm宽1800mm高2100mm
Shape size: 2600 mm long, 1800 mm wide and 2100 mm high
风扇电机 ： 1 5 kw
Fan motor: 15 KW
空压机电机： 7.5 kw
Air compressor motor: 7.5 kw
电加热 : 0. 5kw
Electric heating: 0.5 kw
总功率 : 23kw
Total power: 23 kw
造雪喷嘴 ： 106个
Snow nozzles: 106
核子器： ： 20个
Nucleon: 20
喷嘴圈数 ： 3排
Number of nozzle rings: 3 rows
旋转角度 ： 360度
Rotation angle: 360 degrees
风筒仰角 ： 50度
Wind drum elevation: 50 degrees
造雪温度 ： -35℃～0℃
Snow-making temperature: - 35 ~0 C
出雪量 ： 50～80m3/h
Snow outputm3/h
扬程 ： 40～120m
HeadM
供电电压 ： 380伏
Power supply voltage: 380 volts
快接电源 ： 63A
Fast connection power supply: 63A
结构 ： 3轮胎及可旋转支架
Structure: 3 tires and rotatable brackets
金耀造雪机的优势：自动化 360°旋转 质保长 不堵塞 不结冻
Advantages of Jinyao Snowmaking Machine: Automation 360 degree Rotation Quality Guarantee, Non-clogging and Non-freezing
金耀造雪机使用与保养
Use and Maintenance of Jinyao Snow Maker
开机前检查电源连接处是否有虚连。电压是否稳定。如果是发电机组供电，持续供电不可低于380伏。阀门是否结冰堵塞。如堵塞可开启电加热进行预热。喷嘴，核子器与喷头连接处是否密封。如密封圈老化或渗漏及时更换。确保风机及空压机正转。空压机油液面保持在红线处。造雪时如有结冰要及时清除以免飞溅伤人。每次造雪前检查压力表，气压表泄压阀性能；皮带涨紧度；使用完毕后把管路内余水排清。根据当地水质适当清洗喷嘴和过滤网。轴承,螺栓,伸缩杆,转盘定期注油保持各部件润滑度。每个雪季更换一次机油和空气滤芯。
Check the virtual connection at the power connection before starting. Is the voltage stable If the power supply is from a generator set, the continuous power supply shall not be less than 380 volts. Is the valve frozen and blocked If blocked, electric heating can be turned on for preheating. Is the joint of nozzle, nucleator and nozzle sealed If the seal ring aging or leakage timely replacement. Ensure positive rotation of fan and air compressor. The oil level of the air compressor is kept at the red line. If there is ice during snow making, it should be cleared in time to avoid splashing and injuring people. Check the performance of pressure gauge, pressure relief valve of barometer, belt tightening before each snowmaking, and drain the remaining water in the pipeline after use. Clean nozzles and filters properly according to local water quality. Bearings, bolts, telescopic rods, turntables are regularly oiled to maintain the lubrication of the components. Change the oil and air filters once every snowy season.
更详细参数及其它问题请来电或来厂咨询
For more detailed parameters and other questions, please call or consult the factory.
温馨提示：我工厂所有设备发货方式均为货运物流，运费由地方远近和货物方数决定，具体运费请来电详询，以便造成不必要的误会！
Warm Tip: All the equipment in our factory are shipped by freight logistics. Freight is decided by local distance and the number of goods. Please call for detailed information on the specific freight, so as to cause unnecessary misunderstanding!
PS：产品所有价格均为网上报价，请以实物为准，具体价格请来电详询！！！
PS: All the prices of the products are quoted online. Please refer to the actual products. Please call for detailed information on the specific prices!!!
