全部采用数字校正
增强的速度和压力范围
采用先进的电子和软件技术,一次测试最多可得到45个剪切力或剪切速率数据点
独特的运算法则以测试高分子材料熔体的稳定性
双向通信功能使测试参数可以从PC机
Attaches to process using a single M18
temperature measurement
temperature measurement
Performance Specifications
Melt Flow Index 0.1 D 1500 g/10 min
Viscosity Range 10 D 105 Pa s
Shear Stress 3 D 800 KPa
Shear Rate 0.1 D 4000 s-1 (standard die)
Dies 1 - 11mm
10 to 40:1 L/D
Temp. Range 40 D 350C
Pressure Range 2 x 105D 3.5 x 107 Pa
Metering Pump 0.30 cm3/rpm (standard)
Pump Speed 3 D 75 rpm, servo motor, vector controlled
Measurement and Control Functions
Test Modes
Shear Stress Mode:
Setpoint: Pressure
Measurement: Melt Flow Index
Shear Rate Mode:
Set point: Pump speed
Measurement: Apparent viscosity
Specifications
Electr. Cabinet NEMA 12 (IP 54)
CPU 80188 E-PROM Embedded Applications Program
Operator Interface LCD display
Options
PIV process isolation valve
RS232 / RS485 output
Melt Flow Index 0.1 D 1500 g/10 min
Viscosity Range 10 D 105 Pa s
Shear Stress 3 D 800 KPa
Shear Rate 0.1 D 4000 s-1 (standard die)
Dies 1 - 11mm
10 to 40:1 L/D
Temp. Range 40 D 350C
Pressure Range 2 x 105D 3.5 x 107 Pa
Metering Pump 0.30 cm3/rpm (standard)
Pump Speed 3 D 75 rpm, servo motor, vector controlled
Measurement and Control Functions
Test Modes
Shear Stress Mode:
Setpoint: Pressure
Measurement: Melt Flow Index
Shear Rate Mode:
Set point: Pump speed
Measurement: Apparent viscosity
Specifications
Electr. Cabinet NEMA 12 (IP 54)
CPU 80188 E-PROM Embedded Applications Program
Operator Interface LCD display
Options
PIV process isolation valve
RS232 / RS485 output
4 - 20 mA output (up to two, customer specified)
Hook-up cables
VCU stand
ViscoSensor stand (for horizontal mounting only)
Analog Outputs: (4-20mA standard)
Optional
Melt Temperature
Delta-Pressure
Melt Flow Index
Apparent Viscosity
Interface Requirements
Single standard M18 pressure port required
Other configurations possible
Minimum polymer supply pressure of 1000 psi
for 1.0 MFI material
Electrical Specification
System Voltage 230 VAC 50/60 HZ
Power 1500 W
Mechanical Specification
Weight 35lbs
Height 17ò
Diameter 8ò
Mtg. Configuration Vertical (Stand for Horizontal)
Hook-up cables
VCU stand
ViscoSensor stand (for horizontal mounting only)
Analog Outputs: (4-20mA standard)
Optional
Melt Temperature
Delta-Pressure
Melt Flow Index
Apparent Viscosity
Interface Requirements
Single standard M18 pressure port required
Other configurations possible
Minimum polymer supply pressure of 1000 psi
for 1.0 MFI material
Electrical Specification
System Voltage 230 VAC 50/60 HZ
Power 1500 W
Mechanical Specification
Weight 35lbs
Height 17ò
Diameter 8ò
Mtg. Configuration Vertical (Stand for Horizontal)