机器性能：
1. WINDOWS2000/XP中文操作界面，易学易懂；
(WINDOWS2000/XP Operating interface, easy to learn and understand.)
2. 灌胶形状可实现点、线、面、弧、圆或不规则曲线连续补间及三轴联动等功能，能适应任何不规则物件灌胶；
(Functions of drawing points, lines, surfaces, circle, consecutive complement of irregular curves and three axes linkage available, applicable to any irregular product potting. )
3. 硬盘有超大储存记忆容量，无限量存储程序，无需重新编程，且软体具有区域阵列，平移旋转运算等功能；
(Hard disk has super memory capacity for storage of program, and software has functions of regional array, translation, rotation and computation, etc.)
4. 胶量大小粗细、涂胶速度、点胶时间、停胶时间皆可参数设定、出胶量稳定,不漏滴胶；
(Potting volume, speed, time, and halting time can be set by parameters; glue outflow is quite stable with no leaking or dripping.)
5. 可选配CCD视觉编程系统，实现快速编程；
CCD visual programming optional, realizing fast programming process.
6．采用自动升降门、自动密封机构，减少人工操作，提高工作效率；
(Automatic overhead door, automatic sealing device, decreasing labor operation while increasing efficiency. )
7．采用倍速链输送系统，可配接驳台等设备一体化作业；
(Speed chain conveying system, open to conveyor integration operation. )
8.配备德国贝克真空泵，抽吸流量165m3/h；
(Equipped with BECKER vacuum pump with suction flow rate as 165m3/h. )
9.真空压力表可任意调节参数，真空度达到上限值后真空泵自动停止工作；
(Parameters on the vacuum gauge adjustable, the pump automatically stops working when vacuum degree reaches the limit. )
10.配备安全光栅，确保设备的安全运行；
(Equipped with safety light curtain, make sure the equipment safely work. )
11.配胶、灌胶和轨迹灌封三种功能一体化实现，全自动操作；
((Full automatic process of glue mixing, potting, and various route potting.)
12.按需配比，实现边混合边灌胶，max限度节约胶水；
(Glue mixed as needed before and in the process of potting, saving glue as much as possible.)
13.双料桶设计，A胶和B胶分开储料，保证胶水长时间放置不发生固化；
(Dual glue tanks to store A and B glue separately, helping to store glue for a long time.)
14.混合比例从100：100到100：20或100：20~100：10可调，采用动态或静态混合，混合均匀、充分；
(Mixing ratio adjustable from 100:100 to 100:20 or from100:20 to 100:10, dynamic or static mixing mode optional to ensure fully mixing.)
15.独有的控制系统，不受气压因素影响，避免出胶不均、拉丝、气泡等现象；
(Unique control system helps to avoid uneven potting, drawing and bubble in the potting process without impaction from air pressure.)
16.Z轴高度调整装置能适应不同高度的工件作业；
(Height-adjusting device of Z-axis enables to work for workpiece of different height.)
17.储料桶配有液位感应开关，缺料自动报警；
(Automatic alarming by up /low level materials sensors to avoid short of material.)
18.可选配胶水搅拌、加热并预留真空脱泡功能，适用于不同种类的灌注工艺。
(Optional functions of stirring, heating and vacuum defoamation, fit for various potting /dispensing process.)
